View Profile: 2-stroke demon - Honda TRX250R Forums
No Recent Activity
About 2-stroke demon

Basic Information

About 2-stroke demon
Location:
Miami, fl

Statistics


Total Posts
Total Posts
457
Posts Per Day
0.16
General Information
Last Activity
10-15-2015 03:25 PM
Join Date
10-25-2011
Referrals
0

1 Friend

  1. gusdabus73 gusdabus73 is offline

    Senior Member

    gusdabus73
Showing Friends 1 to 1 of 1

33 Likes

Page 1 of 3 123 LastLast
  1. 02Houser
    02Houser liked post by 2-stroke demon On thread : how to measure a arm's.
    No variables when measuring tierods, once the ends are off you just measure from end to end of bare tierod... All size/brand arms use the same 3 length tierods 13 1/4,14 1/4, & 15 1/4
    Liked On: 12-02-2013, 07:50 AM
  2. american opel
    american opel liked post by 2-stroke demon On thread : how to measure a arm's.
    The measurements I gave are accurate, but have to be taken with the tie rods removed from bike... The ends have to be removed & bare tie rod bar measured
    Liked On: 12-01-2013, 06:32 PM
  3. PROX370R
    PROX370R liked post by 2-stroke demon On thread : So I finally got my laeger arms & hipers on but there's obviously an issue...
    There we go 22358
    Liked On: 10-28-2013, 08:24 PM
  4. PROX370R
    PROX370R liked post by 2-stroke demon On thread : Potential of my pro-x 350 as a laydown dragracer?
    bring your fastest bike down while your at it, no sand here to break your fall though so gotta have balls to run on the asphalt lol... iv got a few bikes you can choose from to run if you think you...
    Liked On: 10-09-2013, 10:36 PM
  5. PROX370R
    PROX370R liked post by 2-stroke demon On thread : Potential of my pro-x 350 as a laydown dragracer?
    Back to my post if anyone with helpful information is around id appreciate it... instead of thread killers that are just a waste of time.
    Liked On: 10-09-2013, 10:36 PM
  6. PROX370R
    PROX370R liked post by 2-stroke demon On thread : Potential of my pro-x 350 as a laydown dragracer?
    Lol, what exactly have I done... started a fight, I don't internet fight. Anyone that has something to say is more than welcome to do it in my face so I can teach a lesson on respect
    Liked On: 10-09-2013, 10:34 PM
  7. jamieg45
    jamieg45 liked post by 2-stroke demon On thread : Show off your R and trikes !!!!!
    Heres a before & after of my bucket of bolts to add... even more changes have been made since, waiting on parts to get delivered 21474 21473
    Liked On: 09-25-2013, 02:06 PM
  8. R man
    R man liked post by 2-stroke demon On thread : I'll take my beating now......
    I recently got rid of mine, had issue after issue with it tearing the chassis apart, hauled ass but ended up taking out second gear & traded the bike. id suggest billet rear hubs, I spun both of...
    Liked On: 09-24-2013, 06:54 PM
  9. JoePA
    JoePA liked post by 2-stroke demon On thread : CT 350 cylinder
    can either call ct & have them set you up with a new flat top wiesco, cost around $180... or have your head/dome cut to allow use of either a $150 wiseco or $200 wossner(less heat expansion)
    Liked On: 06-26-2013, 11:36 AM
  10. JoePA
    JoePA liked post by 2-stroke demon On thread : CT 350 cylinder
    Its a 350, with a few bores left, they run a specific flat top wiesco piston only available from ct racing that are cut. I had the dome on my ct350 custom cut to allow use of an off the shelf wiseco...
    Liked On: 06-26-2013, 11:35 AM
  11. JoePA
    JoePA liked post by 2-stroke demon On thread : CT 350 cylinder
    Your welcome, I would just send it all together, but can't tell you that 100% since I don't have a powervalve on mine... would deff have them check out the powervalve for its condition & if it has...
    Liked On: 06-26-2013, 11:35 AM
  12. sky
    sky liked post by 2-stroke demon On thread : Best Engine Builder?
    I understand what you are saying silverlake, but I never even said that Carlos had my cylinder to do dragracing work, hes simply cutting a new dome & reboring my cylinder. As far as I personally am...
    Liked On: 06-26-2013, 11:28 AM
  13. Burns350R
    Burns350R liked post by 2-stroke demon On thread : Best Engine Builder?
    Very true but there's a way to go about trying to call someone out, then there's just plain bashing... All they do is fuck up everyones posts, including mine. Sound more like internet bullies lol. I...
    Liked On: 06-26-2013, 09:11 AM
  14. Burns350R
    Burns350R liked post by 2-stroke demon On thread : Best Engine Builder?
    Is it just me or are atvfan & duner simply the biggest haters of bdt around? All I see is both of you jumping on any post and bashing him... to me sounds like your both just dick pulling each other,...
    Liked On: 06-26-2013, 09:11 AM
  15. atv fan 28
    atv fan 28 liked post by 2-stroke demon On thread : Best Engine Builder?
    Is it just me or are atvfan & duner simply the biggest haters of bdt around? All I see is both of you jumping on any post and bashing him... to me sounds like your both just dick pulling each other,...
    Liked On: 06-26-2013, 08:47 AM
Page 1 of 3 123 LastLast